Listing of components
Refer to the diagram below to better visualize the location of the various installation components.
INSTALLATION GUIDE PAKPAR™-GPS
IMPORTANT
BEFORE PROCEEDING WITH THE INSTALLATION!
This document provides all the information needed for the proper and safe installation of your PAKPAR™ system.
Before proceeding with the installation or configuration of the PAKPAR™ system, the installation technician must first have read and understood the instructions provided in this guide.
This document contains important information to prevent the risk of serious injury to both installation technicians and users.
Informations - General Module
As a result of the change in SAAQ regulations on heavy vehicles and tippers, PAKPAR™ has created its own security system and dump body checker. Using its integrated GPS, this system will take into consideration the speed of the vehicle and will allow the control of the alarm’s light and sound as required by SAAQ regulations. It is easily installed on all types of dump vehicles.
- TAKES THE VEHICLE SPEED INTO ACCOUNT
An audible safety warning sounds at 12 km/h - COMPLIES WITH NEW SAAQ REGULATIONS
New regulations in force from September 2020 - EASY INSTALLATION
In addition to being robust and reliable, the installation is simple and identical for each model of bucket lift - COMPLETE KIT TO SAVE TIME
Includes management module, warning buzzer, LED light and bucket lift sensor
Technical specifications
Operating voltage
10 to 16 Vdc
Operating temperature
-40°C to 75°C (-40°F to 167°F)
Power consumption
Input voltage 12 Vdc
Standby mode, bucket closed: 4mA
Monitoring mode (no load): 140 mA (max)
Output available
12V, 1A (2)
Input available
12V, 10mA (4)
PAKPAR™
Module Only
(without harness or accessories)
PAKPAR-KIT
Complete Kit
1 | PAKPAR-LED
Red LED Light
2 | PAKPAR-BUZZER
Warning Buzzer
4 | PAKPAR-H-MAIN
Main Connection Harness
5 | PAKPAR-H-EXT-25
25' Detector Extension
6 | PAKPAR-PROXIMITY
Proximity Detector
Explanations and operation
The PAKPAR™ system allows the control of audible and luminous alarms that indicates if the dump body is lifted when the vehicle speed exceeds 12 km/h and this feature is programmable.
LED Output
This begins to flash as soon as the dumper is lifted more than 5cm depending on the location where the detector is installed irrespective of vehicle speed.
Bucket Buzzer Output
It activates for only 5 seconds when the speed is under 10km/h (+/-2km/h) as soon as the dump body is raised more than 5 cm depending on where the detector is installed.
Constantly activates a beeping sound once the vehicle speed exceeds 10km/h (+/-2km/h) and if the dump body is lifted by more than 5 cm depending on where the detector is installed.
Auxiliary Buzzer Output
Constantly activates a beeping sound when the auxiliary input #2 is active. An example of what it does is that it allows for the detection of low oil level for the pump. Note that any other detector could be used here.
NOTE : The module will assume the dump body is raised if the detector is disconnected.
The status LEDs on the PAKPAR™ module allows for a quick check of the module status.
LST
Indicates the general status of the module:
- 1 flash every 4 seconds = standby module (dump body closed)
- 1 flash every second = module activated (dump body raised)
GPS
Indicates that the number of satellites available by the GPS are sufficient for speed detection.
LSS
Indicates that the dump body detector is well connected and helps to install the latter.
General connection diagram
Simplified connection diagram
INSTALLATION ROLL-OFF | GARBAGE TRUCK | BUCKET LIFT
- LED Light
Is in the cab of the truck - Warning Buzzer
Is in the cab of the truck - GPS Antenna (ANT-GPS-960)
Is in the cab of the truck - Main Connection Harness
Is in the cab of the truck - Extension for the Detector
Wiring for connection between the main PAKPAR™ module and the proximity detector - Proximity Detector
Lies under the truck bed
Installation Extension PAKPAR-H-EXT-25
In order to limit the size of the hole to be passed for the 25 foot extension on a « single dump » type truck installations, the Deutsch™ female connector is not installed. Once the thread is passed, simply use the part provided in the kit.
Positioning of the wiring
RED - Position C
BLACK - Position B
WHITE - Position A
Installation proximity detector
Suggested location: In front of the bucket
NOTE : This proximity detector is IP67 certified, but it must be protected from various debris that could reach it on the road. It can be installed in any direction and anywhere on the body or on any other metal accessory.
Installation GPS Antenna | ANT-GPS-960
The installation of the GPS antenna must be done in the cab of the truck. Make sure that the antenna has a direct view of the outside (eg. windshield). The antenna can be attached in two (2) ways:
- Magnetic | Put on a metal surface
- Velcro | Use the velcro supplied with the kit
Suggested Location
Here is the suggested location inside the cab to maximize the effectiveness of the GPS antenna. On the passenger side dashboard near the windshield.
Limited warranty PAKPAR™
PAKPAR™ offers a 24 months guaranty period from the date of purchase or delivery for all the components it produces. All products made by PAKPAR™ verified, inspected, and certified to be free from all manufacturing defects. If a product is found to be defective during the warranty period of 24 months, this product will be repaired or replaced at the discretion of PAKPAR™ at the workshops of PAKPAR™. Any installation, use, or modification of products or components manufactured by PAKPAR™ not recommended by the manufacturer will void this warranty.
PAKPAR™ will take no responsibility for any cost or damage incurred from the misuse, negligent operation, or any repairs attempted or carried out by third parties. Any other warranty, written or verbal, other than that provided by PAKPAR™ will not be recognized.
PAKPAR™ also reserves the right to repair or replace any defective product at its will. PAKPAR™ assumes no responsibility for expenses incurred during the installation or removal of a product requiring maintenance and/or repair.
It is expressly stated that we will not be bound by any other warranty, express or implied, of inherent quality, merchantability or fitness for a particular purpose.
